Standards and Service Limits
|
2-2 | |||||
| Item | Measurement | Qualification | Standard or New | Service Limit |
| Ignition coil | Rated voltage | 12 V | ||
| Firing order | 1 - 3 – 4 - 2 | |||
| Spark plug | Type | D14Z5, D15Y6, D15Y4, D16W7 engines | NGK: ZFR5J-11 DENSO: KJ16CR-L11 |
|
| D17A1, D17A2, D17Z1, D17Z4 engines | NGK: ZFR6J-11 DENSO: KJ20CR-L11 |
|||
| D17A5, D17Z5 engines | NGK: ZFR6J-11 DENSO: KJ20CR-L11 |
|||
| D15Y2, D15Y3, D16W8, D16W9 engines | NGK: BKR5E-11 DENSO: K16CR-L11 |
|||
| D17Z2, D17Z3 engines | NGK: ZFR6J-11, ZFR7J-11 DENSO: KJ20CR-L11, KJ22CR-L11 |
|||
| D14Z6, D16V1 engines | NGK:ZFR5J-11, ZFR6J-11 DENSO: KJ16CR-L11, KJ20CR-L11 |
|||
| Gap | 1.0-1.1 mm (0.039-0.043 in.) | - | ||
| Ignition timing | At idle (check the red mark) | M/T (in neutral): 8+2° BTDC at 700+50 rpm (min-1) | ||
A/T HONDA MULTI MATIC (in  or  ): 8+2° BTDC at 700+50 rpm (min-1) |
||||
| Alternator belt NOTE: Adjust a new belt to the new belt spec., run the engine for 5 minutes, then readjust it to the used belt spec. |
Deflection with 98 N (10 kgf, 22 lbs) applied midway between pulleys | Without A/C (with A/C, see "Compressor belt" in the A/C table) | Used belt: 8.5-11.0 mm (0.33-0.43 in.) | |
| New belt: 6.5-8.5 mm (0.26-0.33 in.) | ||||
| Tension (measured with belt tension gauge) | Without A/C (with A/C, see "Compressor belt" in the A/C table) | Used belt: 340-490 N (35-55 kgf, 77-110 lbs) | ||
| New belt: 540-740 N (55-75 kgf, 120-170 lbs) | ||||
| Alternator | Output | At 13.5 V and normal engine temperature | 70 A | |
| Coil (rotor) resistance | at 68°F (20°C) | 1.84-2.10 ohms | ||
| Slip ring O.D. | 22.7 mm (0.89 in.) | 21.7 mm (0.85 in.) | ||
| Brush length | 19.0 mm (0.75 in.) | 5 mm (0.20 in.) | ||
| Brush spring tension | 3.3-4.1 N (1.6-1.8 kgf, 3.5-4.0 lbs) | |||
| Starter for D15Y2, D16W7 (KG model), D16W8, D17Z1 (Except Malaysia model), D17A1, D17A2 (Except Malaysia model), D17A5 (Except Indonesia model) engines (DENSO) | Output | 1.0 kW | ||
| Commutator mica depth | 0.50-0.75 mm (0.020-0.030 in.) | 0.2 mm (0.008 in) | ||
| Commutator runout | 0.02 mm (0.001 in.) max. | 0.05 mm (0.002 in) | ||
| Commutator O.D. | 27.9-28.0 mm (1.098-1.102 in.) | 27.0 mm (1.063 in.) | ||
| Brush length | 14.0-14.5 mm (0.55-0.57 in.) | 9.0 mm (0.35 in) | ||
| Brush spring tension | 13.7-17.7 N (1.4-1.8 kgf, 3.09-4.00 lbf) | |||